Hi,
I am trying to read data from the Denver Instrument Mass Balance. I am using the "Basic Serial Read and write.vi" as the block diagram from Labview 8.0 help. But after all the connections it is only reading the bytes that are sent to the serial port and not the exact mass reading from the mass balance.
Please help me out with the vi.
Subhayan
LAbview 8.0 reading data from Denver Instrument Mass Balance
-
IvanLis
- guru
- Сообщения: 5464
- Зарегистрирован: 02 дек 2009, 17:44
- Награды: 7
- Версия LabVIEW: 2015, 2016
- Откуда: СССР
- Благодарил (а): 28 раз
- Поблагодарили: 87 раз
Re: LAbview 8.0 reading data from Denver Instrument Mass Bal
You must know the interface (baud rate, the structure of the transmitted packet) and a description of the protocol that is used for data transmission. Without such information will be difficult to implement the program independently.Subhayan писал(а):Please help me out with the vi.
Contact the manufacturer or its representative to provide such information.
Знание нескольких принципов освобождает от знания многих фактов!
Правила форума
Как добавить в сообщение картинку или файл
Конвертация / версий (форматов) VI
Как правильно задать вопрос...
Правила форума
Как добавить в сообщение картинку или файл
Конвертация / версий (форматов) VI
Как правильно задать вопрос...
-
- interested
- Сообщения: 3
- Зарегистрирован: 06 июл 2011, 23:54
- Версия LabVIEW: 8.0
- Контактная информация:
Re: LAbview 8.0 reading data from Denver Instrument Mass Bal
I know the baud rate etc. I am using a RS 232 port for the handshaking. I have synchronized the instrument with the software. My problem is should i change the flow control to RTS/CTS or XON/XOFF because the manual doesnot say anything about how the flow control should be. It's able to read the bytes but not the exact mass with the "Basic Serial Read and write.vi".
-
IvanLis
- guru
- Сообщения: 5464
- Зарегистрирован: 02 дек 2009, 17:44
- Награды: 7
- Версия LabVIEW: 2015, 2016
- Откуда: СССР
- Благодарил (а): 28 раз
- Поблагодарили: 87 раз
Re: LAbview 8.0 reading data from Denver Instrument Mass Bal
watch video, where I tried to show how interactions are managed signalsSubhayan писал(а):My problem is should i change the flow control to RTS/CTS or XON/XOFF because the manual doesnot say anything about how the flow control should be.
may need to control (switching) operation modes for your device, that is to include a mode in which the transmitted information
Знание нескольких принципов освобождает от знания многих фактов!
Правила форума
Как добавить в сообщение картинку или файл
Конвертация / версий (форматов) VI
Как правильно задать вопрос...
Правила форума
Как добавить в сообщение картинку или файл
Конвертация / версий (форматов) VI
Как правильно задать вопрос...
-
mzu2006
- doctor
- Сообщения: 2456
- Зарегистрирован: 16 авг 2008, 02:12
- Награды: 3
- Версия LabVIEW: 7.1 10 11 12
- Откуда: St-Petersburg (RU), Phila, Boston, Washington DC
- Контактная информация:
Re: LAbview 8.0 reading data from Denver Instrument Mass Bal
Subhayan, You absolutely have to know the protocol for your device. I.e. you have to prompt your device to transmit that mass-balance data to you. Some of the protocols are proprietary, but call up a tech support first, they will likey point you to proper manual.
As with Xon/Xoff RTS/CTS there are only 4 possible combinations. try them all - chose the one that works.
As with Xon/Xoff RTS/CTS there are only 4 possible combinations. try them all - chose the one that works.
Правила форума (Forum rules in Russian)
rm -rf /mnt/windows
rm -rf /mnt/windows
-
- Похожие темы
- Ответы
- Просмотры
- Последнее сообщение
-
- 0 Ответы
- 1894 Просмотры
-
Последнее сообщение Anastasia
-
- 3 Ответы
- 2065 Просмотры
-
Последнее сообщение PozhiloyGoblin
-
- 0 Ответы
- 343 Просмотры
-
Последнее сообщение maxim_MA
-
- 23 Ответы
- 2396 Просмотры
-
Последнее сообщение dadreamer
-
- 2 Ответы
- 390 Просмотры
-
Последнее сообщение ujin1